Honeywell Fire Alarm Systems

Morley Multi Detector

The multi-criteria Photo Thermal detector uses thermal assistance to the core photoelectric smoke detector to give enhanced false alarm immunity and faster response to a wide range of incipient fires. The plug-in unit combines two separate sensing elements that are managed by embedded software to act as a single unit. The Multi-Criteria Detector conforms to EN54-5, a 58°C fixed temperature and rate of rise thermal, with the smoke detection element conforming to EN54-7

MHR-1 SYSTEM SENSOR SOUNDER

Information Name : Red Mini Horn Red UL certified India, System Sensor, Category : Conventional Notification Appliances, Fire, Products, Sounder

MULTICRITERIA PHOTOTHERMAL SENSOR

The 2351TEM photoelectric smoke/thermal detector incorporates an optical chamber and a thermal element, which in turn are continually monitored by an on board processor by using algorithms developed specifically for the unit. An alarm signal is only enabled in the detector once the processor is satisfied that an incipient fire has been detected. By using a combination of inputs, the incidence of nuisance alarms is reduced while at the same time, the response time to an actual fire is also improved.

MCP2A-R470SF-01 MANUAL CALL POINT RESETTABLE TYPE

Red Conventional Call Point with LED and Resistor 470 OHM Flush Mounting Flexi Element, System Sensor Category : Conventional Initiation Devices, Fire, Manual Call Point, Products

Honeywell Heat Detector System Sensor

The System Sensor 5602 is a 5600-series, 194°F fixed temperature, rate-of-rise, single-circuit, mechanical heat detector. The 5602 detector offers a low-cost means for property protection against fire, and for non-life-safety installations where smoke detectors are inappropriate.

STANDALONE BATTERY OPERATED CONVENTIONAL Detector System Sensor

This smoke alarm is a battery operated smoke detector that utilizes photoelectric sensing technology. When the smoke concentration on the site reaches the alarm threshold or the test button is pressed and held down, the LED of the alarm will turn from slow flashing to quick flashing and will give out sound alarm signals. When the smoke concentration drops below the alarm threshold or the test button is released, the alarm will recover to its normal state (the Alarm state is not locked, the LED will restore to slow flashing and the alarm will stop).

MI-DISO ISOLATOR MODULES Morley

Name : Loop isolation module. Requires M200E-SMB for surface mounting or M200E-DIN for mounting to DIN rails., Honeywell International, Inc, Morley-IAS Category : Addressable Module, Fire, Isolators, Products

SYSHS 24V DC SOUNDER WITH STROBE SYSTEM SENSOR

Mounting plate included for compatibility with a wide range of back box sizes Three field selectable candela settings: 15, 75, and 115 Easy to use rotary dials for selection of candela and horn settings Built in synchronization feature keeps strobes in sync for up to 30 minutes Strobes Listed to UL 1638; Horns Listed to UL 464 Horn settings on the horn strobe model include high and low volume, continuous or temporal 3 tone Universal Fire symbol is language independent

MI-DCMO ADDRESSABLE CONTROL OUTPUT MODULE Morley

The Morley-IAS MI-DCMO control output module is used with the ZX series of intelligent conrol panels to provide either a single alarm circuit or Form C relay. The MI-DCMO can be used to operte dry contacts for door holders, air handling unit shut down or other similar functions. Optionally the module can be used to supervise wiring to the ouput load providing monitoring of the external load voltage or power supply

Morley Heat Detector

The HM Series Advanced intelligent thermal sensors are plug-in type fire sensors that use a single thermistor sensing circuit to provide early warning of developing fires, together with addressable communication with the fire panel. The HM-RHSE, HM-RHSE-I provides fixed 58°C and rate-of-rise (10°C / minute) temperature sensing (Class A1R). The HM-FHSE, HM-FHSE-I provides fixed 58°C temperature sensing (Class A1S). These sensors are designed for open area protection and must only be connected to fire panels that use a compatible proprietary communication protocol for monitoring and control. The detectors have two integral red LEDs that provide 360° local visual indication of the device status.

GREEN MANUAL CALL POINT EMERGENCY DOOR

Name : Green Manual call point Emergency door release, System Sensor, Category : Conventional Initiation Devices, Fire, Manual Call Point, Products

CONV MCP GREEN DUAL POLE FLEXI WITH BB I

Anti-Tamper facility Enhanced aesthetics Backward compatibility

MI-DMMI MONITOR MODULE MORLEY

The MI-DMMI and MI-DMM2I monitor modules are used with the Morley-IAS intelligent fire alarm control panels to provide a single or dual input circuit from external devices. Each input is continuously monitored for normal, open circuit and alarm conditions. Changes to the status of the input circuits are communicated to the panel where the appropriate actions may be undertaken.

Honeywell Smoke Detector System Sensor

Honeywell Firelite CMF-300 A Addressable Control Module

Honeywell Morley DXC1 Single Loop Panel

Honeywell Notifier FMM1 Monitor Module

Morley Smoke Detector (HM PSE AP)

The photoelectric smoke sensor delivers high responsiveness, reduced sensitivity to dust and false alarms resulting from ingress of insect and other debris. The plug-in unit uses sophisticated processing circuitry that incorporates smoothing filters to help eliminate transient environmental noise conditions that can be the cause of unwanted alarms. The devices are managed by embedded software running complex algorithms that further improve resilience to false alarms and improve detection speed.The HM/PSE optical smoke detector has two integral red LEDs that provide 360° local visual indication of the device status

PLUG IN BASE CONVENTIONAL

The B401 is a 2-wire base for use with 400 Series smoke detectors.

SYSTEM SENSOR 2 ZONE FIRE ALARM CONTROL

oneywell System Sensor Fire Alarm Control Panels have been developed to provide a simple and reliable solution to the demands of today’s fire detection solutions. The panels have been designed with both installer and end user’s requirements in mind suited for small to medium sized buildings like Commercial Buildings, Banking, Residential complexes, Retail Units/ Stores, Shops, Restaurants, Healthcare, Public Offices, Schools etc

MI-DCZRM Addressable Zone Monitor Module

The MI-DCZRM addressable zone monitor module allows a zone of non-addressable devices to communicate with a Morley-IAS protocol analogue addressable system. As a result existing non-addressable zones can be integrated into a Morley-IAS protocol system.